9-19不銹鋼高壓風機 9-19不銹鋼高壓風機一般用于鍛冶爐及高壓強制通風機，可廣泛用于輸送物料，輸送空氣及無腐蝕性不自然，不含粘性物質及氣體。介質溫度一般不超過80℃，介質中所含塵土及顆粒不大于150mg/m³。
產品型式:該風機為A式傳動：風機無附加軸承支承，葉輪與電機直聯傳動。機號有NO3.15、3.55、4、4.5、5、5.6、6.3七種?？芍瞥捎倚妥笮齼煞N型式，葉輪順時針旋轉，稱為右旋風機。以“右”表示，葉輪逆時針旋轉，稱為左旋風機，以“左”表示。風機的出口位置，以機殼的出風角度表示，9-19不銹鋼高壓風機NO3.15~6.3出廠時均做成多種型式，可根據使用單位要求安裝成所需的位置，即出風口位置調整范圍0°~225°或45°，即（0°、45°、90°、135°、180°、225°）共六種，用戶根據需求制成一種方向角度。
結構特點:本風機主要由葉輪、外殼、進氣口、電機、連接器、冷卻風扇葉片等組成。葉輪：由10個后傾的機翼型葉片、曲線型前盤和平板后盤組成，并經過動平衡校正，氣動性能，故運轉平衡、振動小、效率高、壽命長等特點。機殼：用鋼板焊成蝸型殼體。進風口：制成整體（全部模具成型），裝于風機的側面，于軸向平行的戴面為曲線形狀，能使氣體順利進入葉輪，且損失較小。

9-19 Stainless steel high pressure fan 9-19 Stainless steel high pressure fanGenerally used in forging furnace and high pressure forced fan can be widely used for conveying materials conveying air and non-corrosive unnatural free of viscous substances and gases. The temperature of the medium is generally not more than≤80℃ and the dust and particles contained in the medium are not more than 150mg/m3
Product type:The fan is A type drive: the fan is not supported by additional bearings and the impeller is directly driven by the motor. There are seven kinds of machine numbers: NO3.15, 3.55, 4, 4.5, 5, 5.6 and 6.3. Can be made into right-handed and left-handed two types the impeller rotating clockwise called right-handed fan. In & other; Right & throughout; That the impeller rotates counterclockwise called the left cyclone to “ Left & throughout; Said. The outlet position of the fan is expressed by the outlet Angle of the housing. The 9-19 stainless steel high-pressure fan NO3.15~6.3 is made into various types when leaving the factory. It can be installed into the required position according to the requirements of the user that is the adjustment range of the outlet position is 0° ~ 225° Or 45°、 That (0°、 45°、 90°、 135°、 180°、 225°) A total of six kinds the user according to the demand to make a direction Angle
Structure features:The fan is mainly composed of impeller housing air inlet motor connectors cooling fan blades etc. Impeller: Composed of 10 backward leaning wing blades curVILinear front disc and plate rear disc and through dynamic balance correction aerodynamic performance so the operation balance small vibration high efficiency long life and other characteristics. Housing: welded with steel plate into a cochlear housing. Air INLET: MADE into a WHOLE (all mold molding) installed on the side of the fan parallel to the axial surface for curve shape can make the gas smoothly into the impeller and the loss is small